Hayward c48k2n143b3 manual

[Kolari]

Hayward c48k2n143b3 manual
.
.
Download / Read Online Hayward c48k2n143b3 manual
.
.
.

.
HZ Models are not UL or CSA Listed. To prevent potential injury and to avoid unnecessary service calls, read this manual carefully and completely. This product should be installed and serviced only by a qualified professional. A licensed electrician MUST complete, in full, all electrical installations noted in this manual. Hayward replacement parts voids warranty. Top element. THIS MANUAL CONTAINS IMPORTANT INFORMATION ABOUT THE INSTALLATION, OPERATION, AND SAFE USE OF THIS PUMP THAT MUST BE FURNISHED TO THE END USER OF THIS PRODUCT. Pool and spa components have a finite life. All components should be inspected frequently and replaced at least every ten years, or if found to be damaged, broken, cracked, missing, or not securely attached. COM USE ONLY HAYWARD GENUINE REPLACEMENT PARTS. CPSC guidelines, follow all national, state, and local codes applicable. Installation of a vacuum release or vent system, which relieves entrapping suction, is recommended. Failure to install according to all defined instructions may result in severe personal injury or death. General Information Introduction This manual contains information for the proper installation and operation of the Hayward Super Pump Series. The instructions in this manual MUST be followed precisely. Failure to install according to defined instructions will void warranty. It is recommended that a minimum length of piping, equivalent to 10 pipe diameters, be used between the pump suction inlet and any plumbing fittings. All electrical wiring MUST be performed by a licensed electrician, and MUST conform to local codes and NEC regulations. CLOSE VALVES in suction and outlet pipes. RELEASE ALL PRESSURE from pump and piping system using filter manual air relief valve. Insure air vents are free from obstruction to avoid damage. Do NOT use water to hose off motor. Occasionally, shaft seals must be replaced, due to wear or damage. Replace with genuine Hayward seal assembly kit. To reduce risk of injury, do not permit children to use this product. Disconnect all electrical power service to pump before beginning shaft seal replacement. Only qualified personnel should attempt rotary seal replacement. Contact your local authorized Hayward Dealer or service center if you have any questions. SPX1600Z1M SPX1605Z1M SPX1607Z1M SPX1610Z1M SPX1615Z1M SPX1620Z1M WWW. Contact qualified professional to check that the wiring gauge is heavy enough. The motor will automatically shut off if power supply drops before heat damage can build up causing windings to burn out. Motor bearings noisy from normal wear, rust, overheating, or concentration of chemicals causing seal damage which will allow chlorinated water to seep into bearings wiping out the grease causing bearing to whine. All seal leaks should be replaced at once. To obtain warranty replacements or repair, defective components or parts should be returned, transportation paid, to the place of purchase, or to the nearest authorized Hayward service center. For further Hayward dealer or service center information, contact Hayward customer service department. No returns may be made directly to the factory without the express written authorization of Hayward Pool Products, Inc. Hayward pool pumps have always been our leading line of pumps. Hayward pumps come in a variety of horsepowers, voltages and speeds. Typically, any dilemmas with your Hayward pool pump are likely related to either electrical or plumbing situations. With the information explained in this comprehensive troubleshooting guide, you can diagnose and repair your Hayward single speed or variable speed pool pump with ease! If you get no response from your Hayward pool pump when you flip the switch, first verify the terminal board connections match the wiring diagram on the motor data plate label. Likewise, check if the motor is wired correctly for the available field supply voltage. Check all connections, circuit breakers, and fuses. Repair or replace any tripped breakers or blown fuses. Inspect the motor shaft for any obstructions. Remove the pump and basket, then look for and remove any debris in the shaft. If the pump motor makes a humming sound when starting up, you likely have a clogged impeller. To remedy this, simply open up your pump, and clean out any rubbish. Damaged or inadequate wiring, resulting in a power drop, are likely to blame for your Hayward pool pump shutting off. Fixing this issue can be tricky, so we suggest you get the help of a certified professional. Improper voltage wiring is the usual culprit for smoking pump motors. Check the motor diagram for the voltage wiring diagram. Loose wire connections or touching terminal connections cause sparking. Fix this problem simply by tightening or adjusting the wires and connections in the motor. Sparking can also come directly from a short in the windings of the motor. A jammed impeller or blown capacitor can lead to a tripped breaker. In some instances, it could just be a bad breaker. If you susp filexlib.
.
Hayward c48k2n143b3 manual lawn
Hayward c48k2n143b3 mode d’emploi
Hayward c48k2n143b3 bedienungsanleitung
Hayward c48k2n143b3 manual
Hayward c48k2n143b3 manualidades

[投稿者]

投稿